ORIENTA
Orienta is the rolling shutter with adjustable slats.
A synthesis between a roller blind and a shutter, it only offers the best of both products. Often, when using roller blind
we have to choose whether to pull up the blind to let in fresh
air or lower it to provide protection from the sun and privacy.
In a single solution, Orienta allows you to ventilate, illuminate and protect your house from the sun under entirely safe
conditions. It works without any mechanisms inside the rails,
which means it can be installed as a normal roller blind both
in new and existing buildings.
It does not require any maintenance and ensures consistent
operation over time. The product can be operated manually,
a winch or a drive unit. On the market, there are motors with
a radio control featuring three limit stops. You can save the
wound blind, closed blind and adjusted blind positions.
We recommend using motors with a low rpm value, preferably 12 – 15 rpm.
TECHNICAL INFORMATION
- Blind weight 9 kg al m2
- Number of slats per metre in height 18
- Centre distance between closed slats 54.9 mm
- Centre distance between open slats 63.5 mm
- Please note that 5 non-orientable slats are added on top near the octagonal roller.
TECHNICAL SECTIONS
CREATING THE EXACT BLIND MEASURE
The exact blind width is obtained by subtracting 8-10 mm from the
internal rail measurement. (Only for the rails shown in this catalogue).
IMPORTANT: the internal measurement of the rails that has always
to be 18 mm (see rail section on the next page).
(adjustable slats)
(fixed slats)
WINDING DIAMETERS FOR ROLL (70 mm)*
NOTE: When using 60 mm roll, please subtract 10 mm from values shown
below.
ARCHITECTURAL | 1600 | 1800 | 2000 | 2200 | 2400 | 2500 | 2800 | 3000 |
WINDING DIAMETER mm | 195 | 200 | 215 | 225 | 230 | 240 | 250 | 255 |
ARCHITECTURAL | 1600 | 1800 | 2000 | 2200 | 2400 | 2500 | 2800 | 3000 |
WINDING DIAMETER mm | 210 | 220 | 230 | 240 | 250 | 260 | 270 | 280 |
NOTE: Once set the rolling diameter please add 30 mm tolerance in order to make the rolling work properly into the box
INTERMEDIATE SUPPORTS (inner view)
Intermediate reinforcement supports will be used based on the length:
ORIENTA
(internal rolling)
ORIENTA REVERSE
(external rolling)
(outer view)
edge slat up to L. 3000 mm
side supports kit
central supports kit
TUBULAR MOTORS
TECHNICAL DATA | MAT45ECA/Y | MAT45ECA/Y | MAT45ECA/Y | MAT55ECA/Y | MAT55ECA/Y |
Nominal force (N.m) | 20 | 30 | 50 | 80 | 100 |
Nominal speed (rpm) | 15 | 15 | 12 | 12 | 10 |
Diameter (mm) | 45 | 45 | 45 | 55 | 55 |
Nominal voltage (V) | 230 | 230 | 230 | 230 | 230 |
Nominal frequency (Hz) | 50 | 50 | 50 | 50 | 50 |
Nominal frequency (Hz) | 145 | 191 | 205 | 385 | 393 |
Nominal current (A) | 0,64 | 0,83 | 0,89 | 1,65 | 1,68 |
L₁/L₂(mm) | 738/620 | 645/624 | 760/750 | 613/597 | 771/756 |
I All tubular motors are provided with:
- Electronic end-limit
- Intermediate end-limit
- Built-in radio receiver
- Slats opening setting
Other models available on request.
RAILS AVAILABLE (note: rails working width is between brush holders)
AT50009
Rail 22×31
in extruded aluminium
AT50010
Made by measure
with brush (7X5)
AT50013
Rail 26.5×68 ORIENTA
in bars
AT50014
Made by measure
with brush
AT50018
Rail 26,5×31,5 in extruded
aluminium for
ORIENTA in barse
AT50019
Made by measure
with brush
AT36016
Extruded aluminium rail
con spacer 65 in bars
AT36017
Made by measure
with brush
AT36012
Top closure for spacer in extruded
aluminium bars
AT36013
Made by measure with brush
Renolit light
AT50011
Rail 150×68 ORIENTA
in bars
AT50012
Made by measure
with brush
AT50015
Double rail 69×60
in bars paired to rails mod.
AT50009/AT50010
ACCESSORIES
AT36020
Fast nylon graft for closing
AT36012 with screws for
upper closing – black
ZMV01T
Self-drilling screw 4,2×16
for fast graft applying
AT31005
Adjustable
support for
standard
mullioned
AT31004
Orientable support
for standard
mullioned
AT31007
Wood support
with bearing
AT31006
Bearing with iron
bushing
AT31003S
Bearing holder
support
adjustable with screw
AT50000
Security latches
TUBULAR MOTOR ACCESSORIES
For motor MAT45ECA/Y
MAT006
Mounting bracket
MAT008
Adjustable support
MATS04
Adapter for
70 mm
octagonal barrel
MAT005
Mounting bracket
For motor MAT55ECA/Y
MAT010
Mounting bracket
MAT015
Mounting bracket with adjustable
upper support 50 N/m
REMOTE CONTROL
MAT501
Single-channel remote control
Every channel can control up to
20 receivers
Power supply:
3V CR2450 battery
duration: more than 2 years
Transmission frequency:
433.90MHz ± 100KHz
Dimensions:
130mm×44mm×10.5mm
MAT502
15 channels remote control
Eah channel can control up to
20 receivers
Power supply:
3V CR2450 battery
duration: more than 2 years
Transmission frequency:
433.90MHz ± 100KHz
Dimensions:
130mm×44mm×10.5mm
MAT503
Single-channel wall controller
No cabling required
fully installable when
needed
Power supply:
3V CR2450 battery
duration: more than 2 years
Range capacity:
200 m outdoor, 35 m indoor
Transmission frequency:
433.90MHz ± 100KHz
Dimensions:
80mm×80mm×11.7mm
COLOR GAMMA FOR THE BLINDS
The colour references reported in this catalogue might appear altered by the reproduction
and printing process.
For greater safety, please refer to the colour
sample book provided by the company
NOTE: For glossy or matte RAL colours, the product is understood as out of warranty. Please
contact the company in advance for more information.
NON-STANDARD COLOURS:
Surcharges on ral base gamma price list): RAL
BASE +20% – RAFFAELLO +30% – WOOD +50%
For orders less than 20 sqm please contact us in advance.
Note: price is calculated based on exact blind surface.
RAL
* WHITE 9010
* MOSS GREEN
* GREY 7035
* GREY 9006
* GREY 7016
MOSS
** MOSS GREEN
** MOSS BROWN
RAFFAELLO
** RAFFAELLO GREY
WOOD
** GRAINED WHITE
** DOUGLAS
** CHERRY WOOD
** LIGHT WALNUT
** MEDIUM WALNUT
** DARK WALNUT
** OAK
** GOLDEN OAK
** NUSSBAUM
** GRAINED GREEN
COLOR GAMMA FOR RAILS
Rails can be ordered with same color of the blinds, except the wood
colors.
For colors Ral 9010 – 1013 – 7035 – 9006 – 7016 no surcharge is applied.
For colors Muschio e Raffaello + 10%
For non-standard colors please contact us in advance.
Prices are VAT excluded and can be subject of variation without info.
Subject to misprints and improved design changes.
HOW TO ORDER
Place your order by specifying:
- The size of the finished blind for the width
- The architectural light (i.e. under the head box) for the height. The rolling shutter will be provided in a larger size to ensure it operates correctly.
DECLARATION OF PERFORMANCE N° 01AV
Product id code | ORIENTA 2.0 |
Product description | Rolling shutter with adjustable slats, without any |
Usage | Outdoor sun protection, according to standard |
Manufacturer name | MV LINE SPA Italia |
Product evaluation and | Applied system for product evaluation and |
| Declared performance | |||
| Wind resistance class UNI EN 13659:2013 | Architectural light dimensions | Performance | |
| Width up to (mm) | Height up to (mm) | ||
| 2000 | 2500 | 6 | |
| 2500 | 2000 | 6 | |
| 3000 | 2400 | 4 | |
| AVVOLGIBILE ORIENTA 2.0 CON STECCHE IN POSIZIONE CHIUSA | ||||
|---|---|---|---|---|
| Colore | BIANCO | PASTELLO | SCURO | NERO |
| gTot | 0,026 | 0,044 | 0,062 | 0,079 |
| Classificazione UNI EN 14501:2006 | 4 | 4 | 4 | 4 |
| AVVOLGIBILE ORIENTA 2.0 CON STECCHE IN POSIZIONE APERTA | ||||
|---|---|---|---|---|
| Colore | BIANCO | PASTELLO | SCURO | NERO |
| gTot | 0,102 | 0,098 | 0,094 | 0,090 |
| Classificazione UNI EN 14501:2006 | 3 | 4 | 4 | 4 |
WARRANTY
In order to use the warranty it is mandatory to write the PRODUCT
CODE in the white space below. You can find the product code on the
label coming with the product package (see fig. 1) and attach the purchase receipt (tax receipt or invoice).
